Brake adjustment limit checker
Pick each brake chamber's type, enter the pushrod stroke you measured, and see which brakes are within the federal readjustment limit, which are over, and how close the truck is to an out-of-service count.
BY JEFF BYRD· TRUCK DISPATCHER, 8 YEARS IN TRUCKING· HOW WE CHECK
FREE · 49 CFR 393.47(e) · CHECKED 2026-10-12
TAP A BRAKE, ENTER ITS MEASURED STROKE
Vehicle
Brake 1: Steer left
LIMIT 1 3/4 IN. · IN ADJUSTMENT
BRAKE CHECK · ESTIMATE
- SERVICE BRAKES
- 10
- OVER THE 393.47 LIMIT
- 1
- COUNTED DEFECTIVE (CVSA)
- 1
- SHARE DEFECTIVE
- 10%
| # | POSITION | STROKE / LIMIT |
|---|---|---|
| 1 | Steer left | 1 3/8 / 1 3/4 |
| 2 | Steer right | 1 1/2 / 1 3/4 |
| 3 | Drive 1 left | 2 / 2 1/2 |
| 4 | Drive 1 right | 2 1/8 / 2 1/2 |
| 5 | Drive 2 left | 2 1/8 / 2 1/2 |
| 6 | Drive 2 right | 2 1/4 / 2 1/2 |
| 7 | Trailer 1 left | 2 1/4 / 2 1/2 |
| 8 | Trailer 1 right | 2 1/2 / 2 1/2 |
| 9 | Trailer 2 left | 2 1/16 / 2 1/2 |
| 10 | Trailer 2 right | 2 3/4 / 2 1/2 |
1 brake is past the federal readjustment limit. That's a violation even below the out-of-service line. Get them adjusted and find out why: automatic slack adjusters shouldn't need it.
Limits from 49 CFR 393.47(e). Out-of-service count estimated from published summaries of the CVSA criteria. Not a substitute for a qualified brake inspector.
Truck in the shop for brakes? Tell your dispatcher early and we rebook the pickup, instead of you racing a deadline on bad brakes.
Message the dispatch deskHow the checker decides
Every air brake chamber has a maximum applied pushrod stroke, set by its type in 49 CFR 393.47(e). Past that point the brake can't push the shoes hard enough, and stopping distance grows. The checker compares each measurement with its chamber's limit, then counts the truck as a whole.
LIMIT = 393.47(e) table value for the chamber type IN ADJ. = stroke < limit AT LIMIT = stroke = limit (legal, but adjust soon) OVER = stroke > limit (violation) DEFECTIVE = 1 per brake 1/4 in.+ over, 1 per 2 brakes less than 1/4 in. over SHARE = defective / service brakes; 20%+ = likely out of service
ASSUMPTIONS
- Strokes are entered to the nearest sixteenth of an inch, the way they're read on a ruler.
- Limits are the federal table values. For a chamber the table doesn't list, the rule caps stroke at 80% of the rated stroke marked on it.
- The defective count follows published summaries of the CVSA out-of-service criteria. Inspectors use the current CVSA edition, which can change; treat the share as an estimate.
- Steering axle brakes and other brake defects (cracked drums, air leaks, missing parts) are judged separately and aren't counted here.
How to measure applied pushrod stroke
Measure on level ground with the wheels chocked. Build air pressure to roughly 90 to 100 psi, shut the engine off, and release the spring brakes. Mark the pushrod where it leaves the chamber, then have a helper hold a full brake application while you measure how far the mark moved. That distance is the applied stroke.
- 1Chock the wheelsLevel ground
- 2Build airAbout 90-100 psi, engine off
- 3Mark the pushrodBrakes released
- 4Full applicationMeasure the mark's travel
If you work alone, some drivers use a brake pedal holder. Never crawl under a truck that isn't chocked, and keep hands away from the slack adjuster while the brakes are applied.
Semi truck brake chambers: types and limits
A brake chamber's type number is its effective diaphragm area in square inches, so a type 30 has 30 square inches pushing on the pushrod. Bigger chambers sit on the drive and trailer axles; steer axles often use types 16 to 24. Long-stroke chambers allow more travel and have higher limits; the manufacturer marks them. If you can't confirm a chamber is long-stroke, ask your shop before you rely on the higher limit.
| Type | Standard stroke | Long stroke |
|---|---|---|
| 6 | 1 1/4 in. | - |
| 9 | 1 3/8 in. | - |
| 12 | 1 3/8 in. | 1 3/4 in. |
| 16 | 1 3/4 in. | 2 in. |
| 20 | 1 3/4 in. | 2 in. (2 1/2 in. if 3 in. rated) |
| 24 | 1 3/4 in. | 2 in. (2 1/2 in. if 3 in. rated) |
| 30 | 2 in. | 2 1/2 in. |
| 36 | 2 1/2 in. | - |
49 CFR 393.47(e) · checked 2026-10-12
Why brakes drift out of adjustment
Air-braked trucks built on or after October 20, 1994 must have automatic brake adjusters and, where the pushrod is exposed, an adjustment indicator (49 CFR 393.53). So a brake that's out of adjustment usually means something is wrong: a worn or seized slack adjuster, a bent bracket, worn cam bushings or linings near their limit. Cranking an automatic slack adjuster back by hand hides the problem for a few days. Have it inspected instead, and write down every stroke reading with its date, so a wheel that keeps drifting shows up in your records before it shows up at a scale house.
49 CFR 393.53 · checked 2026-10-12
Hydraulic brakes on box trucks and hotshots
Pushrod stroke limits only apply to air brake chambers. Many 26 ft box trucks and most hotshot pickups stop with hydraulic brakes, which have no external pushrod to measure. For those, 49 CFR 393.47 sets a minimum lining or pad thickness instead: no hydraulic or electric brake may run with less than 1/16 inch at the shoe center. Check pad wear at every tire rotation, and treat a soft or sinking pedal as a reason to stop.
Reading your result
One brake over the limit is a violation. Enough of them together takes the truck off the road.
GREEN
All within limits
Every stroke is under its chamber's limit. Recheck on the schedule your shop sets, and after any brake work.
AMBER
At or slightly over
Brakes at the limit are legal but have no room left. Brakes over it are violations. Get them looked at before the next trip.
RED
Out-of-service range
Defective brakes reach 20% of the total. Expect to be placed out of service at an inspection. Don't drive until it's repaired.
A planning check, not an inspection. Brake work belongs with a qualified brake inspector. Not legal advice.
Free tools for this run
Safe equipment, planned loads, your call on each one
When the truck needs shop time, we rebook around it. Every rate con comes to you to confirm or turn down.
Apply for dispatch