Skip to content
DISPATCH DESK OPEN 24/7MESSAGE THE DESK
MileCaptain

Tire tread depth legal checker

Tap each tire on the drawing and enter its tread depth in 32nds of an inch. See which tires pass the federal minimum, which are close, and roughly how many miles each axle group has left.

BY JEFF BYRD· TRUCK DISPATCHER, 8 YEARS IN TRUCKING· HOW WE CHECK

FREE · 49 CFR 393.75 · CHECKED 2026-10-12

TAP A TIRE, ENTER ITS TREAD IN 32NDS

Vehicle

910121212121212121288883888

Steer, left

MINIMUM 4/32 · LEGAL

Miles left estimate (optional)

Tires going on the truck this week? Tell your dispatcher the shop day and we plan the loads around it.

Message the dispatch desk
01THE RULE

How the checker decides

Federal rules set two numbers. Steer tires, the ones on the front axle of a truck or tractor, need at least 4/32 of an inch of tread. Every other tire needs at least 2/32. The checker compares each tire with the number for its position.

STEER MINIMUM  = 4/32 in.  (front wheels, truck or tractor)
OTHER MINIMUM  = 2/32 in.  (drive, trailer, tag)
LEGAL          = depth >= minimum for the position
CLOSE          = depth < minimum + 2/32
WEAR RATE      = (new depth - worst depth) / miles run
MILES LEFT     = (worst depth - minimum) / wear rate

ASSUMPTIONS

  • Depth is the shallowest reading in a major tread groove. The rule says to measure away from tie bars, humps and fillets, the raised bits in the groove floor.
  • The close band is 2/32 above the minimum, roughly the margin you'd want before a long run. It's our planning margin, not a rule.
  • Miles left assumes the tire keeps wearing at the same rate. Alignment, load and road type change that fast.
  • Original depth varies by tire model. Use the manufacturer's spec for your tire, not the starting numbers here.
02DEPTH CHART

Truck tire tread depth chart

There are only two legal numbers to remember, but where you are between new and the minimum tells you when to book tires. The chart shows the federal minimums against a 32nds ruler. Anything at or below the red line for its position has to come off the truck.

PositionLegal minimum
Steer (front wheels)4/32 in.
Drive2/32 in.
Trailer2/32 in.
Box truck rear, hotshot dually2/32 in.

49 CFR 393.75(b), (c) · checked 2026-10-12

TREAD DEPTH, 32NDS OF AN INCH
0481216204/32 STEER MINIMUM2/32 DRIVE, TRAILER6/32 · STEER, PLAN NEW TIRES
03MEASURING

How to measure semi truck tire tread depth

Use a tread depth gauge, not a coin. Push the probe into a major groove, the deep channels that run around the tire, and read the shallowest spot across several points around the tire, because tires wear unevenly. Skip the raised tread wear indicators in the groove floor: they show a worn-out tire at a glance, but they are not a measuring point. On duals, check the inner tire too; it's the one that gets missed.

Major groove

The deep channels around the tire, not the shallow sipes.

Skip the bars

Tie bars, humps and fillets in the groove floor don't count.

Shallowest point

Read several spots around the tire and keep the lowest.

Inner duals

The tire nobody looks at wears just as fast.
04OTHER TIRE RULES

Tread depth isn't the only tire rule

A tire with plenty of tread can still be illegal. Federal rules bar any tire with exposed body ply or belt material, tread or sidewall separation, a flat or audible leak, or a cut down to the ply. Regrooved tires rated 4,920 pounds or more can't go on the front wheels of a truck or tractor. Tires can't carry more weight than the sidewall rating, and cold pressure can't be below what the load needs.

05CDL TEST

What is the minimum tread depth for front tires on the CDL test?

4/32 of an inch for steer tires, and 2/32 for the rest. CDL pre-trip tests ask about it because steer tires matter most: a front blowout takes the steering with it. Say the numbers out loud during the pre-trip portion of your skills test, along with the other tire checks.

06WEAR PATTERNS

What uneven wear is telling you

A tire that wears evenly reaches its minimum slowly and predictably. One that doesn't is a warning about the truck, not just the tire. Wear on one shoulder points to alignment. Wear down the center often means too much air; both shoulders, too little. Cupping or scalloped patches suggest worn shocks or a balance problem. Fix the cause when you replace the tire, or the new one goes the same way.

07READING THE RESULT

Reading your result

Start with the red tires, then plan the amber ones into your next shop visit.

GREEN

Legal with room

More than 2/32 above the minimum for the position. Keep checking at every pre-trip; tread can go fast on a misaligned axle.

AMBER

Legal, replace soon

Within 2/32 of the minimum. Book tires before the next long run so you aren't buying them at a truck stop on the road.

RED

Below the minimum

Not legal to run. Replace the tire before the truck moves under load.

08FAQ

4/32 of an inch, measured in a major tread groove, for the front-wheel tires of a truck or truck tractor (49 CFR 393.75(b)). Measure away from tie bars, humps and fillets.

A planning check, not an inspection. Not legal advice.

TFREE TOOLS

Good rubber, good loads, your decision on each

We plan around your shop days and your clock. Every rate con comes to you to confirm or turn down.

Apply for dispatch

DISPATCH APPLICATION · 60 SECONDS

Stop chasing loads. Let our desk do it.

Three quick steps. A dispatcher calls you back, learns your lanes and your clock, and starts booking. Nothing moves without your yes.

  • 5% of gross for 1 truck · 4% for fleets · 7% new MC
  • No setup fee, no contract, cancel with 30 days notice
  • Every rate con comes to you. Say yes or no.
  • Loads planned around your 11, 14 and 70
1
2
3
What are you running?

Pick your equipment. 26 ft box trucks and up.

TAKES 60 SECONDS · A DISPATCHER CALLS YOU BACK, NOT A BOT